The Foundation of Plumbing Skills for Bathtub Installation
The Foundation of Plumbing Skills for Bathtub Installation
Blog Article
What are your ideas about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Mounting a bath tub isn't precisely brain surgery, but it does call for strong plumbing, woodworking, and occasionally, tiling abilities. Changing an old bathtub with a new one is additionally a moderately challenging job. If the old bathtub is easily obtainable, the job can move speedily; if you have to open up a wall to get rid of the old bathtub and also place the brand-new tub, the task is a lot harder. In either case, the task is within a house handyman's abilities, although you will certainly require an assistant to leave the old bathtub and embeded in the brand-new one. Make sure you have actually qualified on your own for the job and fit trying it. As opposed to working with a contractor to take over a halfway-completed job, it is far better to consider employing one before you begin. Possibilities are you might require an expert plumber to make tube connections.
This write-up will certainly aid you install a brand-new bathtub in your washroom if you have actually currently purchased a new bathtub as well as do not require to transform the arrangement of your previous water pipes.
Your tools as well as material list ought to make up the following:
Planning for the Setup
To start with, the sustaining frame provided with the bath ought to be fitted (if required) according to the supplier's instructions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is very important to make certain that if the faucet comes with a plastic washing machine, it is fitted between the bathroom as well as the faucets. On a plastic bathroom, it is likewise practical to fit a sustaining plate under the taps system to avoid strain on the bathtub.
Fit the adaptable faucet ports to the bottom of the two faucets making use of 2 nuts and also olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you use all of the provided washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath need to currently be ready to be suited its final setting.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is detach the water supply. After doing so, switch on the taps to drain pipes any type of water staying in the system. The procedure of eliminating the existing faucets can be rather troublesome due to the restricted accessibility that is typically the instance.
Make use of a container wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the taps. Have a towel ready for the staying water that will originate from the pipelines. When the supply pipes have been gotten rid of, utilize the very same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from transforming during this process. Once the taps have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing substance.
Before moving on to fit the new taps, compare the pipe links on the old faucets to the brand-new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.
Setting up the Bath tub
Utilizing the two wood boards under its feet, put the bathtub in the needed placement. The wood boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
The next objective is to make certain that the bathtub is leveled all round. This can be achieved by examining the spirit level and adjusting the feet on the bath tub till the level checks out level.
To install taps, fit the bottom of the outermost adaptable tap port to the ideal supply pipeline by making a compression join; then do the very same for the various other tap.
Activate the supply of water and also examine all joints and new pipework for leaks and also tighten them if essential. Load the bath tub and likewise inspect the overflow electrical outlet and the normal electrical outlet for leakages.
Ultimately, fix the bathroom paneling as explained in the supplier's user's manual. Tiling and also securing around the bath tub ought to wait up until the bath tub has been made use of at least once as this will resolve it right into its last placement.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will require a plastic adapter to prevent damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the other end supplies a connection to the current supply pipelines.
If you need to fit a monobloc, then you will require reducing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin making certain that the washers are in location between the tap and also the sink. Secure the faucet in position with the supplier given backnut. Once the tap is securely in place, the supply pipes can be linked to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The former kind must be connected to the tap finishes initially, tightening only by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bath satisfies the ceramic tile, it is required to secure the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to break a rigid seal, causing the water to penetrate the wall between the bath as well as the tiling, leading to problems with moisture and possible leakages to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your components and also installations. They are offered in tubes as well as cartridges, and are capable of sealing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can fill it with twists of drenched newspaper or soft rope. Remember to always load the bath tub with water before securing, to allow for the activity experienced when the tub remains in use. The sealant can fracture fairly very early if you do not take into account this motion before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also conveniently readily available on the marketplace. It is recommended to fit the floor tiles making use of waterproof or waterproof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like more info about How to Install a Bathtub Yourself? Post a short review down the page. We'd be delighted to know your reactions about this review. Hoping that you come back again later on. Liked our review? Please share it. Help another person discover it. Thank you so much for taking the time to read it.
24-hour service? Dial here. Report this page